Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player

Rubbish Chute
24" diameter Rubbish Chute as manufactured by Wilkinson Chutes and specified below:
Chute Material
The Chute shall be fabricated of #16 U.S. Gauge Aluminized Steel, Galvanneal or stainless steel (304-430).
Durable Construction
to ensure your chute the longest life available we build only the finest equipment. No rivets, bolts or other protrusions project into the chute riser. All vertical joints are continuously welded for maximum strength. Each floor has a fully supported integral expansion joint.
Throat Design
Throat design never in the line of trash slope to ensure the largest clear opening at the intake while reducing the possibility of damage from the impact of falling material to a minimum.
Intakes
Several dimension available, stainless steel, self-closing, positive latching, bottom-hinged, hand operated doors bearing 1-1/2 Hr. 250° F U.L. "B" label. Intake door to pivot on a concealed 1/2" steel pivot shaft to prevent build-up of debris. (Specify masonry or drywall installation.) Intake doors to be furnished with removable stainless steel door trim with embossed letters (RUBBISH).
Discharge
Wilkinson Type "A", normally open, inclined rolling door with fusible link. Discharge door panel to be fabricated to "B" label construction (1" thick insulation) even if U.L. Label is not required.
Chute Cleaning
A Disinfecting and Sanitizing (D&S) unit equipped with adjusting screw to regulate the strength of disinfectant introduced into the flushing water, connected to flushing head spray head,. On-off valve on unit permits ability to by-pass disinfecting and sanitizing unit when desired. All D&S units require 15" x 15" high side-hinged stainless steel access door bearing a U.L "B" label.
Sprinklers
1/2" IPS 165 degree sprinkler head with shield above top intake. Additional 1/2" sprinklers and shields at every second intake (or as required by Code). 3/4" IPS flushing spray head centered in chute above top intake ready for connection by plumber.
 
Linen Chute
Soiled linen is usually bagged or bundled before it is loaded into the chute. Therefore, the side hinged doors with large clear openings are used most often on linen chutes. Our doors, with specially designed cantilevered brackets, provide a full 180 degree opening to alleviate broken closures as experienced on other designs. Hospitals generate about 15 pounds of soiled linen per bed per day. (Hotels and motels a little less).
Chute Material
The Chute shall be fabricated of #16 U.S. Gauge Aluminized Steel, or stainless steel chutes and fittings.
Intakes
21" wide x 21" high, stainless steel, self-closing, positive latching, side hinged, hand operated doors bearing 1-1/2 Hr. 250 °F U.L. "B" label. (Specify masonry or drywall installation.) Intake door to have 180 degree      swing operation and be furnished with removable stainless steel door trim with embossed letters (Soiled Linen).
Discharge
Type "H" hopper with 24" wide x 30" high, top hinged, counterbalanced stainless steel door bearing 1-1/2 Hr. 250° F U.L. "B" label with fusible link. Reinforced bottom with #13 gauge impact plate. Hopper to be supported with a 2" pipe pedestal and equipped with 2" IPS drain flange for connection by plumber.
Vent
Provide full diameter vent 4'-0" above roof with metal explosion cap.
Floor Frames
Fabricate floor frames of 1-1/2" x 1-1/2" x 3/16" angles and 1-1/2" x 3/16" bar stock welded assembly.
Sprinklers
1/2" IPS 165 degree sprinkler head with shield above top intake. Additional 1/2" sprinklers and shields at every second intake (or as required by Code). 3/4" IPS flushing spray head centered in chute above top intake ready for connection by plumber.
 
 
Copyright © 2011 Egytam, All Rights Reserved.
Website Hosted & Designed by RamaHost.
Home :: Profile :: Products :: Brands :: Order now :: Contact us